在隔熱斷橋鋁型材制造中，開齒穿條機是一種用于在鋁型材上進行加工的設備。它主要用于在鋁型材的隔熱斷橋部位開槽，并為隔熱條的安裝提供準確的穿孔。下面由有十多年的機器研發經驗的濟南歌德瑞斯機械設備為您帶來開齒機穿條機的相關知識。

In the manufacturing of thermal insulation broken bridge aluminum profiles, the toothed threading machine is a device used for processing on aluminum profiles. It is mainly used for slotting the insulation bridge section of aluminum profiles and providing accurate perforation for the installation of insulation strips. Below, Jinan Gede Ruisi Mechanical Equipment, with over ten years of experience in machine research and development, will bring you relevant knowledge about gear cutting and threading machines.

　　開齒穿條機的保養知識：

Maintenance knowledge of toothed threading machine:

　　為保證機器的良好運行，在運行過程中若有異常情況應立即停車檢查。排除故障后再重新啟動。設備出現較大的的故障時應有專業人士來維修，在開始檢修前切忌關掉總電源。

To ensure the good operation of the machine, if there are any abnormal situations during operation, it should be stopped immediately for inspection. After troubleshooting, restart. When there is a major malfunction in the equipment, it should be repaired by professionals. Before starting maintenance, it is important to avoid turning off the main power supply.

　　1、傳動維護： 各傳送輥軸承、毛刷輥軸承、傳送軸承、鏈輪、齒輪定期加注鈣基潤滑脂；微型擺線針輪減速機每半年加鈣基潤滑脂一次；無級調速器每半年換Ub—l或Ub—3型潤滑油一次，且在運轉過程中應時常檢查其油位，保持油位在滑標中心線以上。

1. Transmission maintenance: Regularly add calcium based lubricating grease to the bearings of each conveyor roller, brush roller, conveyor bearing, sprocket, and gear; Add calcium based grease to the micro cycloidal gear reducer every six months; The stepless speed controller should replace Ub-l or Ub-3 lubricating oil every six months, and its oil level should be checked regularly during operation to keep it above the centerline of the sliding mark.

　　2、水路維護： 水箱內循環水應每天更換，水箱每周清洗一次，經常檢查噴水嘴噴水情況，項發現堵塞應及時清理。

2. Waterway maintenance: The circulating water in the water tank should be replaced every day, and the water tank should be cleaned once a week. The spray nozzle should be checked regularly for water spraying, and any blockage should be cleaned in a timely manner.

　　3、風路維護： 定期檢查中空玻璃生產線風機運行情況，如有異常聲音應立即停機檢查，定期清洗風機過濾柵，減小引風阻力，提高風干后玻璃表面潔凈度。

3. Wind path maintenance: Regularly check the operation of the fans in the insulated glass production line. If there is any abnormal sound, stop the machine immediately for inspection. Regularly clean the filter screen of the fan to reduce the induced air resistance and improve the cleanliness of the glass surface after drying.

本文由 開齒穿條機 為您精心提供，如想了解更多請點擊我們的網站：http://m.mybmiformula.com，我們將會以最大的熱情為您解答!

This article is carefully provided by a toothed threading machine. If you want to learn more, please click on our website: http://m.mybmiformula.com We will answer you with the greatest enthusiasm!